" "
How to: fitting TM Designworks’ Slide n Glide chain guide kit

TM Designworks Slide n Glide chain guide and rear sprocket protector kit workshop fitting guide. 

 

Resting firmly as one of those forgotten parts on our bikes, chain guides actually play a huge role – helping guide the chain is only the half of it. Used and raced at the highest off-road races by the KTM, Husqvarna and Sherco Factory teams, the TMDesignworks chain guides are designed to be a like-for-like replacement.  

They also help protect the swingarm and rear sprocket, help prevent chain jump and wheel lock-up and help reduce power losses due to excess chain movement as you ride.

We understand the basic principle to provide better chain protection and reduce friction, lowering surface drag and chain plate wear. But here’s a fact we hadn’t realised until we engaged brain to write this feature: the reduction of friction has an impact on power – of course it does we hear you cry. TMD also say the lower frame pad and chain guide reduce loss of power over jumps due to less chain movement and drive chain control. 

 
TMDesignworks Chain guide Set Enduro21 560
 

What’s in the Slide n Glide kit?

The TM Designworks ‘Slide n Glide’ kit consists of their Dirt Cross front chain slider, Powerlip lower frame pad, and Factory Edition 2 rear chain guide – you can buy the parts individually but opting for this full kit saves you a few dollars.

Fitting guide:

Removal of the stock parts is easy enough with just a handful of tools – in fact the whole job took us less than an hour to complete. We’ve used our test mule Husqvarna FE350 but this kit fits most 2011-onwards KTM and 2014-onwards Husky off-road and enduro models.

First task was to loosen slightly the front sprocket bolt (follow manufacturer’s instructions on this) before removing the chain completely and the rear wheel. The front sprocket protector needs to come off and after that we took the front sprocket off.

 
TMDesignworks Chain guide removal stock Enduro21 560
 

More or less it is two bolts all the way with this job. Next are the two retaining the rear chain guide followed by the chain protector ahead of the chain guide which bolts in with cupped washers top and bottom of the swingarm (the top one on ours was caked in dirt and needed cleaning out before the 8mm socket would connect). 

Just a single bolt holds the standard lower frame slider ‘pad’ undone from the inside/backside of the footrest mount.

Clean and keep all the bolts removed (you need some to refit with new parts) plus give the swingarm a good clean and remove any dirt or old thread lock from the bolt holes.

Refitting

The new parts from TMD basically bolted straight in so we followed reverse order with every step. Use the OEM bolts or the replacement bolts and washers which come in the pack (instructions in the pack explain which to use and also say to check length of each before use). The new TMD parts come fitted with spacers and sleeves and in all cases we used a dab of thread lock on the bolts on refitting. NB: check the manual for torque settings and do not over-tighten the bolts. Swingarms are pretty thin skinned and you can strip the threads if you’re over-zealous. 

 
TMDesignworks Chain guide refitting threadlock Enduro21 560
 

The lower frame slider or pad as TMD describe it (behind the kickstand mount point in the picture above), can go either way around depending on your model of bike so double-check this. 

With the sprocket torqued-up and the chain back on, we made a point of following TMD’s recommendation to check chain slack after installation and using minimum amount – 55mm on most KTM/Husky models – rather than maximum (don’t use the old two finger method because we haven’t all got 22.5mm fingers!).

 
TMDesignworks Chain guide refitting Enduro21 560
 

With the TM Designworks Slide n Glide kit fitted we naturally conducted a thorough seat of the pants test (spinning the back wheel before pushing it around the back yard!). It showed a marked improvement in the free running of the back wheel but we will report back on this after a full and proper test. 

Fast facts:

  • The Factory Edition 2 rear chain guide and sprocket protector accepts any sized o-ring chain and up to two tooth larger rear sprocket. 
  • The stock chain guard that sits up top of the swingarm, between tyre and chain, does not fit with the new rear TMD rear chain guide. A little trimming of the lug on the lowest mount (on the stock guard) would persuade it and you’d need to drill a small hole in the top TMD slider for the front mount bolt. But many people do not refit this part and check pro bikes from FactoryONE Shercos or Factory KTM/Husqvarna WESS riders and you’ll see they don’t use it.
  • The wear pad on the rear guide is replaceable for around $25.
  • USA customers get a six-month wear warranty (check with you local supplier elsewhere). 
  • This kit works with most KTM (2011-onwards) and Husqvarna (2014-onwards) off-road/enduro models.
  • TMD sliders use a UV additive to prevent colour fade and material from drying out and cracking.
 
TMDesignworks Chain guide rear Enduro21 560
 

Fitting time: 1 hour

Cost: $159.95/£130/€145

Colours: Husky dark blue, Swiss blue, Black, Orange

More information and worldwide stockists: TMDesignworks.com

 

Photo Credit: Enduro21
 
 
 
 
Byline jp ISDE 2018 Enduro21
Jon Pearson
Enduro21 Editor and Bike Tester
jon.pearson@enduro21.com